Venstar T1900 User Manual Page 83
- Page / 108
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 17.3
Dry Contact Programming
VACATION MODE OR SERVICE THE CONDENSATE DRAIN PAN -
If Vacation is selected in step #42 (below), when the dry contact is
energized and the thermostat will be forced into Vacation mode
(Section 20).
If Service Pan is selected, when the dry contact is energized the
thermostat will lockout Y1 (compressor) and write Service Pan on
the display.
Press the PROGRAM button to leave the Setup screens. If no buttons are
pressed, the display will leave the setup screens after 30 seconds.
PROGRAM
Press
Service Pan
Vacation
Setup
42
PROGRAM
MODE
MODE
Vacation
Press the MODE button. While holding
the MODE, press the PROGRAM
button to enter Setup screens.
Press the MODE button repeatedly
until this setup screen appears.
S
Y1 when the dry contact is
energized. Select Vacation to
enable Vacation setpoints
when the dry contact is
energized.
elect Service Pan to lockout
Connect wires to a time
clock or other device to
force the thermostat into
Vacation mode.
Y1
G
R
C
MISC2
CK1
CKGND
W1/O/B
MISC1
RS+5
RS1
RSGND
W2
RS2
MISC3
Y1
G
R
C
MISC2
CK1
CKGND
W1/O/B
MISC1
RS+5
RS1
RSGND
W2
RS2
MISC3
OR
Vacation Service Pan
17
Note: Press the MODE
button momentarily
to move through the
setup screens. Press
and hold the MODE
button to move back-
wards through the
setup screens.
Connect wires to a device that
will complete the circuit betw-
een CK1 and CKGND when the
Condensate Drain Pan is full.
NOTE: If Service Pan is selected and the dry contact was closed at least once, the
Service Pan icon will remain on the display to alert the user that a problem has
occurred. This icon will be cleared once a button is pressed.
Step 42 appears only if step 40 is “YES”.
- Digital 1
- Thermostat 1
- FOR HOME OR OFFICE USE 2
- Tested to Comply 2
- How to Use This Manual 3
- Glossary of Terms 4
- Table of Contents 6
- Section 1 Contents: 7
- Front Panel 8
- Page 1.3 9
- Display Features 10
- SECTION 2 12
- Quick Start 12
- Setting the Clock 13
- Setting the Day 13
- Page 2.3 14
- Using the Fan Button 15
- Section 3 Contents: 16
- SECTION 4 18
- Basic Operation 18
- Manual or Auto-Changeover 20
- Page 4.4 21
- Page 4.5 22
- Page 4.6 23
- Page 4.7 24
- (adjusting setpoints) 25
- SECTION 5 26
- Page 5.2 27
- Viewing the Indoor Humidity 28
- SECTION 6 29
- Programming a Daily Schedule 30
- Page 6.3 31
- Page 6.4 32
- Page 6.5 33
- SECTION 7 34
- Programming the Fan Operation 34
- Programming the Fan 36
- Page 7.4 37
- SECTION 8 38
- Thermostat Display Options 38
- Turning On/Off the Backlight 39
- Locking/Unlocking the Keypad 40
- SECTION 9 41
- Humidification 41
- Page 9.2 42
- Page 9.3 43
- Page 9.4 44
- SECTION 10 45
- Dehumidification 45
- Page 10.2 46
- Page 10.3 47
- Page 10.4 48
- Using the Reheat Function 49
- Using the Dehum Terminal 50
- SECTION 11 51
- Viewing Equipment Run-Times 51
- Page 11.2 52
- Page 11.3 53
- Service 54
- UV Light 55
- Section 12 Contents: 56
- Viewing the Heat Pump and 57
- Page 12.3 58
- Using Emergency Heat 59
- SECTION 13 60
- Dual Fuel Operation 60
- Operate a Dual Fuel System 61
- Three Stage Heat Applications 62
- SECTION 14 63
- Timers and Deadbands 63
- Page 14.2 64
- Adjusting the Cycles Per Hour 65
- Adjusting the Deadband 66
- Before the Next Stage 68
- 2nd Stage Turn 69
- SECTION 15 70
- Using the Programmable Output 70
- Page 15.2 71
- Time-Based Control of the 72
- Programmable Output 72
- AUX 76
- SECTION 16 77
- Installing the Remote Sensors 78
- Controlling or Reading the 79
- Remote Temperature (RS1) 79
- 1) with 80
- SECTION 17 81
- Programming the Dry Contact 81
- Dry Contact Operation 82
- Dry Contact Programming 83
- Energy Save Operation 84
- SECTION 19 85
- Programming Run-Time Alerts 85
- Service Filter 86
- SECTION 20 89
- Programming Vacation Mode 89
- Page 20.2 90
- SECTION 21 91
- Configuring the MISC Outputs 91
- Configuring the Jumpers 92
- Page 21.3 93
- Page 21.4 94
- TEMPERATURE 95
- INCREASE 95
- SECTION 22 96
- Pan UV Light 97
- Page 22.3 98
- SECTION 23 99
- Accessories 99
- SECTION 24 100
- Advanced Setup Table 100
- Accessory Port, 23.1 101
- Drain Pan Overflow 102
- Alarm, see Dry Contact 102
- SECTION 25 103
- Smart Recovery, see 105
- Energy Save 105
- W3, see Jumpers 106
- Y2, see Jumpers 106
- SECTION 26 107
- Warranty 107
- Printed on recycled paper 108
- P/N 88-599 Rev. 1 108
Related products and manuals for Equipment Venstar T1900
Equipment Venstar T2900 User Manual
(113 pages)
(113 pages)
Equipment Venstar T1070 User Manual
(30 pages)
(30 pages)
Equipment Venstar T1075 User Manual
(39 pages)
(39 pages)
Equipment Venstar T2300FS User Manual
(29 pages)
(29 pages)
Equipment Venstar T0051FS User Manual
(24 pages)
(24 pages)
Equipment Venstar T1100REC User Manual
(18 pages)
(18 pages)
Equipment Venstar T1100RF User Manual
(22 pages)
(22 pages)
Equipment Venstar T0140 User Manual
(21 pages)
(21 pages)
Equipment Venstar T0130 User Manual
(25 pages)
(25 pages)
© 2020, manymanuals.com. All rights reserved. | 2.265 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals